Manual_SwitchBranchline

How to switch the branchline (e.g. from A to B, from A to C...)

Only for beamline staff. This procedure is not inteded for users.
IMPORTANT! Before starting to move check that the value in
http://082f-bcs.blcs.elettra.trieste.it/blcs/CENTRAL/PEM1/HEIDENHAIN_20/ASSEZ?ACTION=GET
082 BCS: PEM1: Optical Encoder:MZ-PEM1 positionCENTRAL PEM1 HEIDENHEIM_20 ASSEZ is different from 0 and the STATUS iS 0 (AND NOT 8).
IF STATUS is 8 and encoder is 0 you need to call Michele Turcinovich and ask to reboot the ENCODER (it is not necessary to restart the bcs).

From March 2021

A new position for Branch A was found in Feb 2021. The beam flux in the Endstataion A is about 20% higher at PostHorA Z = -20.5 (21.6 enoder reading) 
Branch PostHorA Z
user units (encoder value)
PreVert Z
(mm, encoder)
A May2024 -21.488 (20.406)
Sept2024 -21.5 (20.4)
-1.574
B May2024 25.486 (-26.568)
Sept2024 24.9 (-26)
-1.574
C ? (0) -1.774

Endswitch pressed

If one of the Z axis switches is pressed, you can move the chamber into the correct position with small motor steps from BCS, watching the Encoder readings on the Heidenhain controller display:

  1. On the main BCS web page, click on PEM1, then go to "(DSM_21) Dig. stepper motor".
  2. Note Z axis position and click on "(6MVREL) Z axis relative move".
  3. Move Z axis step by step. Start with small steps (e.g. -10). When the direction is correct, you can try more steps. Relative movement -100 motor steps, will move Z by about -0.2 mm (on the Heidenhain encoder display).

January 2021

Branch PostHorA Z
user units (encoder value)
A -21.955 (23.062)
B 25.985 (-24.879)
C ? (0)




Before 2021

  PostHorA Z PostHorB Z
A -23 (+23) -63 (+23)
B +25 (-25) -15 (-25)
C 0 (0) -40 (0)

FROM A TO B
1. POSTHORA. Z. Read. It should be UserUnits=-23 (UPDATE: August2014: found -21more flux but Io more noisy), Encoder +23 (Branchline A)

2. POSTHORB. Z. Read. It should be UserUnits=-63 (BRACH A), Encoder +23 (Branchline A). If OVERWRITE or RESTORE message appears, it is likely you have to select OVERWRITE.

3. POSTHORB. Z. Move UserUnits to -15 (OLD VALUE WAS -18), Encoder -25 (OLD VALUE was -22) (Branchline B).

4. POSTHORA. Z. Read. A message OVERWRITE/RESTORE will appear. Press Overwrite. Now you should read: UserUnits=+25 (Told value was +22), Encoder -25 (OLD VALUE was -22)(Branchline A). If OVERWRITE or RESTORE message appears, it is likely you have to select OVERWRITE.

FROM A TO C:
1. POSTHORA. Z. Read. It should be UserUnits=-23 (UPDATED GEN2011. NOTE: THE OLD VALUE WAS -26), Encoder +23 (Branchline A)
2. POSTHORA. Z. Move User Units to 0 (zero). Enc=0.
Prehor -900 (0.5) A--->4503(-14245) C
Prevert -151(64.406) A--->267.975 (5.966) C (31/08/2016)

FROM C TO A
1. POSTHORA. Z. Read. It should be UserUnits=0 Encoder 0 (Branchline C)
2. POSTHORA. Z. Move User Units to -23 (zero). Enc=+23.

FROM C TO B
1. POSTHORB. Z. Read. It should be UserUnits=-40 Encoder 0 (Branchline C)
2. POSTHORB. Z. Move User Units to -15 (zero). Enc=-25

Before starting to move check that the value in 082 BCS: CENTRAL PEM1 HEIDENHEIM_20 ASSEZ is different from 0 and the STATUS iS 0 (AND NOT 8).
IF STATUS is 8 and encoder is 0 you need to call Michele Turcinovich and ask to reboot the ENCODER (not the bcs).

 

Last Updated on Friday, 06 September 2024 13:20